Category Archives: Projects

How To: Step by Step Making a Magnetic Drip Tray

Pictured: Update International (DTS-419) 4″ x 19″ Rectangular Drip Tray, Stainless Steel – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Step by Step instructions for making a magnetic drip try for your Kegerator or Keezer.

This is a project that requires materials and tools. Operate power tools carefully. Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.

By: HBF Reader Andrew Cunje

Materials:

Update International (DTS-419) 4″ x 19″ Rectangular Drip Tray, Stainless Steel – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link
Alternate: DasMarine 19″ Length 4″ Width Rectangular Stainless Steel Beer Surface Mount Drip Tray
4′ of 6x.5 Poplar Wood (actual width is 5.5″)
1’4″ of 6×1 Poplar Wood (actual width is 5.5″) Note: A thicker wood will suffice for this…remember the longer the wood extends down from the joint, the less likely the magnetic bond will break from the leverage applied to the edge of the drip tray.)
4-5ft of Decorative Trim of your choice (Sold in lengths of 8′)
MUST BE 1.25-1.5 inch trim. I used 1.5 which I highly recommend.
3/4″ mounting screws (for magnets) or Epoxy/Gorilla Glue
1″ wood screws
Brad/Finishing Nails
1 large old school hard drive magnets (Bigger with Mounting Holes than newer drives) (Alternative: rare earth neodymium magnets that are .5″ thick (Approximately 8); these can be stacked if you can only find .25″ magnets)
Wood Glue
Wood Putty (Optional)
Wood Stain (Optional)
Tennis Racket Grip Tap (Or an old yellow rubber glove). Anything rubbery and tacky to increase friction against the fridge.

Update International (DTS-419) 4" x 19" Rectangular Drip Tray, Stainless Steel

DasMarine 19" Length 4" Width Rectangular Stainless Steel Beer Surface Mount Drip Tray, No Drain, Silver

Continue reading →

Make an E-Paper Tap Handle!

Pictured: Resin Tap Handle Build using waveshare e-paper display, more info below

waveshare 2.7inch Passive NFC-Powered E-Paper

More Info

Highlighted Features

Novel Passive NFC Technology, No Battery Required, No More Battery Life Trouble
Passive NFC Solution, No Battery Required, No Messy Wiring
To Refresh The Display Content, Use A Smart Phone With NFC Function, Or An NFC Reader, Close To The E-Paper, It'll Be Done In A Few Seconds
Refreshed By Smartphone, Comes With Android APP
Suitable For Price Tags, Asset/Equipment Tags, Shelf Labels, Conference Name Tags...

Learn More

This is a 2.7″ e-paper display that requires no power. I think this would make the basis for a great e-paper kegerator tap handle!

If you put together a build… We’d love to share the details with your fellow homebrewers. Email us the deets.

What are Other’s Saying? Search this product’s Amazon reviews for “tap handle” – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

waveshare 2.7inch Passive NFC-Powered E-Paper Module No Battery Wireless Powering & Data Transfer Provides Android APP Black and White Display – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading →

VIVOSUN 400 GPH Utility Pump + Draft Line Cleaning Builds

VIVOSUN 400GPH Submersible Pump

More Info

Highlighted Features

Dimensions: 4.1'' x 2.52'' x 2.95''; The 5ft. long power cord offers convenient installation; Max Flow Rate: 400 GPH (1500L/H); Max Lift Height: up to 5.3 ft.; Watt: 15W; Voltage: 110-120V
Detachable & Cleanable: This compact water pump is easy to hide or disguise and no additional tools are needed for disassembly and cleaning
A Variety of Outlet Positions: Place the pump flat and choose whichever outlet position suits your needs
Wide Range of Application: High performance energy-efficient pump designed for use in ponds, fountains, waterfalls, hydroponic systems, irrigation systems and other water features
4 Suction Cups: The 4 suction cups are strong and require no extra tools to secure; You can choose vertical or horizontal fixing according to your needs

Learn More

From HBF: Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.

I use a similar pump (different manufacturer, features and specifications) for a recirculating draft line cleaning setup. Note that fittings sizes are different on this pump vs the one I use in that build. Adjust accordingly Another possible homebrewing application would be to set this up for use a part of a recirculating wort chiller setup.

What are Other’s Saying? Search this product’s Amazon reviews for “keg” – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

VIVOSUN 400GPH Submersible Pump(1500L/H, 15W), Ultra Quiet Water Pump with 5.2ft High Lift, Fountain Pump with 5ft Power Cord, 3 Nozzles for Fish Tank, Pond, Aquarium, Statuary, Hydroponics – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading →

One of Digital Pressure Gauge + Spunding Valve Build

Pictured: My Digital Spunding Build that features this gauge. See: Building a Digital Spunding Valve for complete project details

Digital Low Pressure Gauge with 1/4” NPT Bottom Connector and Rubber Protector

More Info

Highlighted Features

1. HIGH ACCURACY: Performance tested & certified accurate to ±1% (Relative Humidity Temperature 25°C) with display resolution of 0.1 psi; FOUR different measuring units to choose: 3.5~ 60 PSI, 0.241 ~ 4 BAR, 0 .241~ 4 KGF /CM², 24.1~ 400 KPA.
2. BATTERY SAVING: Power by 2 x LR03 AAA 1.5V (Included in the package). After measuring, the pressure gauge will turn off automatically after 150s of inactivity to preserve battery life.
3. HIGH QUALITY, shock resistance, vibration resistance and durable.
4. WIDE APPLICATION for measuring gas and air pressure. It applies to these fields of pressure container, automation equipment, matching with laboratory equipment and all vehicles tires including heavy duty ones.
5. One year warranty, unconditionally new replacement or refund for any quality products

Learn More

A possible homebrew application for this is to use it as part of a Spunding Valve Build. A Spunding Valve allows you to ferment under pressure, naturally and precisely carbonate in the keg, fix over-carbonated beers and lots more. See: Build a Spunding Valve

Digital Low Pressure Gauge with 1/4” NPT Bottom Connector and Rubber Protector by Uharbour, Range to 60 psi, Accuracy 1%, Resolution 0.1psi – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. ssprod:B07CXM3ZGT:ptr

Adding a Tri-clamp Fitting to a Homebrew Keg Lid

This article is by Homebrew Finds Reader Kris G. Thank you Kris for your creativity and hard work!

Editors Note: This is an advanced project that requires additional tools, skill and materials. This post outlines the process that Kris took to modify his keg lid with a weldless tri-clamp bulkhead. Product specifications can change over time, double check to make sure that current specifications match your needs.

Adding a Tri-clamp Fitting to a Homebrew Keg Lid

Carboys, conicals, buckets, kegs, etc. There is an ever-growing number of options for fermentation vessels. I recently moved away from carboys to experiment with pressurized fermentation. I didn’t feel like buying anything new, so why not repurpose a corny keg for fermentation? This past year I “right-sized” my batches down to 2.5-3 gallons making a corny the perfect size for fermenting. With a couple modifications (shortened dip tube, hop screen, etc), I had an old 5 gallon corny now as a dedicated fermenter. An added bonus was that it fit perfectly in my temp-controlled chest freezer.

Fermenting in a Keg Using TC Equipped Lid

Related: Fermenting Under Pressure

Commercial Option Now Available, Build Continues Below:

304 stainless steel Cornelius Keg Lid with 1.5″ Tri-clamp Ferrule,NEW Corny Beer Keg Lid 60PSI PRV Food Grade Dry Hopper – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This article contains affiliate links. We may make a small percentage if you use our links to make a purchase. You won’t pay more and you’ll be supporting Homebrew Finds and more content like this. Thank you for your support!

I started seeing some other homebrew fermenters with tri-clamp connections on top. Blogs all around showed them used with blowoff tubes, thermowells, carbonation stones, CIP spray balls, etc. It seemed like a great universal connection with a ton of uses. Most importantly to me, I wanted the tri-clamp connection to build an oxygen-free dry hop dropper (that build is an article for another day).

TC Equipped Lid with Butterfly Valve – Also: Color Coded Keg O-Rings

Read on to see my trials and tribulations while adding a TC bulkhead to my corny lid.
Build note: This is a weldless build. If you’ve got the ability/skill/tools to weld stainless, go for it!

Safety Note: Ensure that you are using all tools properly and wearing all the proper PPE. You will be drilling/cutting metal which is both sharp and hot.

PLEASE BE CAREFUL WHEN FOLLOWING THESE INSTRUCTIONS.
HBF is not responsible for your irresponsibility. At time of this writing, I am fully up to date with my tetanus shot. That may or may not be related…

Supplies

Cornelius keg lid with wideset bail (the lids that have the narrow straight bails don’t leave enough room)
Weldless tri-clamp bulkhead
1-5/8” (41mm) Tungsten Carbide Hole Saw (or step bit)

Editors Note: Note that multiple variations of these products may be available, as such a different version may appear at these links. Double check sizes and features.

Continue reading →

FOUR x Carbonation Caps for PET Bottles – works on gas AND liquid posts

More Info

Highlighted Features

Withstand 60-PSI Carbonation Pressure, Complete No Leaking Sealing O-Ring Design and Huge Upgrade From Old Plastic Version: MRbrew carbonation cap comes with necessary brewing sealing o-rings and washer replacemets to prevent leaks, there is a big flat gasket inside this carbonation cap compared to the old version plastic bottle filling cap, can run your carbonator at 60 psi pressure and hold pressure overnight, beer will not go flat, make a airtight seal and good fit for force carbonation.
Sealing Gasket is Not Easy to Fall Out and Include 5/16 Barb Fitting Spare O-ring: the inside rubber sealing gasket features a right size for being placed tightly inside carbonating cap, which will stay in on its own when unscrewing off bottle filling cap, also provide 5/16'' beer nipple barb sealing o-ring replacements even such o-ring is screwed inside getting well protected. unlike other polished finish carbonation caps, you can grip this plastic carbonation cap easily when removing.
Unique Carbonation Cap Keg Post is Perfect for Ball Lock System and Removable Beer Barb: carbonation cap features a unique keg post that has versatility and ease of use, can connect to both gas and liquid disconnects easily, beer 5/16'' hose barb not only enables carbonation cap to carbonate, but to be used for liquid connections and for cleaning as well. made of healthy plastic, no odors, no burrs or unfinished machining anywhere, will not bring strange smell to the carbonation drinks.
Screws onto Standard 2L Soda Bottles Very Securely: this soda drink bottle filling cap features a great accuracy 1-1/8-8UN female thread that can be comparable to the thread of stainless carbonation cap, merge with the plastic PET bottle threads very smoothly, seals the bottles well without needing much torque, screws on and off of bottles easily creating a perfect tight seal every time, excellent tool if you are making homebrewing and kegging.
Perfect for Various Brewing Occasions and Reduce CO2 Loss when Do Brewing Cleaning: carbonation cap is a cool way to re-carbonate beverage quickly, no foaming, great alternative for growlers, allows you to serve portable home brew beer, soda water, iced tea on barbecue, beach, lake or holiday parties, other outdoor activities, brings big convenience to mobile kegging. also can run the cleaner through beer lines from a small soda bottle preventing a larger keg from wasting more co2.

Learn More

Applications:

PET Bottles as Growlers: These are generally intended to convert 1L and 2L bottles to growlers. Fill up a 1L or 2L PET bottle with your favorite homebrew. Put one of these on (purge the headspace by squeezing if you want to) and then pressurize for transport. This should help to reduce oxygen pickup and maintain carbonation levels.
Fine tune or rapidly carbonate beer: You can also use this cap to rapidly carbonate beer. Same process as for transport, just set your regulator to the proper pressure and shake or agitate the PET bottle to help introduce CO2. Or hook it up to CO2 and let it sit in you kegerator.
Draft Line Cleaning Projects: I have developed three draft line cleaning projects using similar SS Caps – Build A Recirculating Draft Line Cleaning Pump | Mark II Keg and Carboy Cleaner Draft Line Cleaning Pump Conversion | Building a Simple Ball Lock Draft Line Flushing Setup
Related Top Post: Fun with Carbonation Caps!

Some carbonation cap models are universal fit and some work only with gas posts. For draft line cleaning projects to work well, at least in my opinion, the carb cap that’s used needs to be universal. As of this posting, the product page says this works with both liquid and ball lock posts. Check the product description for current specs.

MRbrew Plastic Carbonation Cap, 4 PCS Ball Lock Keg Post 5/16” Beer Line Nipple Barb Homebrew Kegging Soft Soda Drink PET Bottles Counter Pressure Bottle Filling Cap with Spare Sealing Gasket O-rings – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Also: [3 PCS] MRbrew Plastic Carbonation Cap Tee Adapter, Allow Gas In and Beer Out Simultaneously, Homebrew Kegging Soda Beer PET Bottles Ball Lock Type Counter Pressure Bottle Filling Cap 3-Way Connector – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading →

Winkeyes 528 GPH Utility Pump + Our Draft Line Cleaning Builds

Winkeyes Fountain Pump 528GPH with 86″ Lift, 30W Small Submersible Fountain Water Pump for Outdoor Indoor Tabletop Water Fountain, Aquarium, Fish Tank, 5.5ft Power Cord, 3 Nozzles (Green-30W)

More Info

Winkeyes Fountain Pump 528GPH with 86″ Lift, 30W Small Submersible Fountain Water Pump for Outdoor Indoor Tabletop Water Fountain, Aquarium, Fish Tank, 5.5ft Power Cord, 3 Nozzles (Green-30W) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading →

Reader Tip… FOUR x Carbonation Caps for PET Bottles – works on gas AND liquid posts + Fun With Carbonation Caps

Thanks to HBF Reader happylilyeastbrewery for this tip! Let’s be friends! 8 Ways to Connect with HBF

More Info

Highlighted Features

Withstand 60-PSI Carbonation Pressure, Complete No Leaking Sealing O-Ring Design and Huge Upgrade From Old Plastic Version: MRbrew carbonation cap comes with necessary brewing sealing o-rings and washer replacemets to prevent leaks, there is a big flat gasket inside this carbonation cap compared to the old version plastic bottle filling cap, can run your carbonator at 60 psi pressure and hold pressure overnight, beer will not go flat, make a airtight seal and good fit for force carbonation.
Sealing Gasket is Not Easy to Fall Out and Include 5/16 Barb Fitting Spare O-ring: the inside rubber sealing gasket features a right size for being placed tightly inside carbonating cap, which will stay in on its own when unscrewing off bottle filling cap, also provide 5/16'' beer nipple barb sealing o-ring replacements even such o-ring is screwed inside getting well protected. unlike other polished finish carbonation caps, you can grip this plastic carbonation cap easily when removing.
Unique Carbonation Cap Keg Post is Perfect for Ball Lock System and Removable Beer Barb: carbonation cap features a unique keg post that has versatility and ease of use, can connect to both gas and liquid disconnects easily, beer 5/16'' hose barb not only enables carbonation cap to carbonate, but to be used for liquid connections and for cleaning as well. made of healthy plastic, no odors, no burrs or unfinished machining anywhere, will not bring strange smell to the carbonation drinks.
Screws onto Standard 2L Soda Bottles Very Securely: this soda drink bottle filling cap features a great accuracy 1-1/8-8UN female thread that can be comparable to the thread of stainless carbonation cap, merge with the plastic PET bottle threads very smoothly, seals the bottles well without needing much torque, screws on and off of bottles easily creating a perfect tight seal every time, excellent tool if you are making homebrewing and kegging.
Perfect for Various Brewing Occasions and Reduce CO2 Loss when Do Brewing Cleaning: carbonation cap is a cool way to re-carbonate beverage quickly, no foaming, great alternative for growlers, allows you to serve portable home brew beer, soda water, iced tea on barbecue, beach, lake or holiday parties, other outdoor activities, brings big convenience to mobile kegging. also can run the cleaner through beer lines from a small soda bottle preventing a larger keg from wasting more co2.

Learn More

Applications:

PET Bottles as Growlers: These are generally intended to convert 1L and 2L bottles to growlers. Fill up a 1L or 2L PET bottle with your favorite homebrew. Put one of these on (purge the headspace by squeezing if you want to) and then pressurize for transport. This should help to reduce oxygen pickup and maintain carbonation levels.
Fine tune or rapidly carbonate beer: You can also use this cap to rapidly carbonate beer. Same process as for transport, just set your regulator to the proper pressure and shake or agitate the PET bottle to help introduce CO2. Or hook it up to CO2 and let it sit in you kegerator.
Draft Line Cleaning Projects: I have developed three draft line cleaning projects using similar SS Caps – Build A Recirculating Draft Line Cleaning Pump | Mark II Keg and Carboy Cleaner Draft Line Cleaning Pump Conversion | Building a Simple Ball Lock Draft Line Flushing Setup
Related Top Post: Fun with Carbonation Caps!

Continue reading →

Stainless Carbonation Cap for PET Bottles… $9.99 + Draft Line Cleaner Builds

Stainless Steel Carbonation Cap

More Info

Highlighted Features

Heavy Duty Stainless Steel for Carbonation Cap, Perfect Polishing Surface,with two free Food Grade Silicone Seal Rings;
Unique Machined the Carbonation Cap, can fit Both Black Liquid Ball Lock Disconnect and Grey Gas Ball Lock Disconnect;
The Carbonation Cap can fits Most Soft Drink PET Bottles, easy to Counter Pressure Bottle Fill PET Bottles;
The Carbonation Cap can Carbonate Various Beverages, including Soda, Beer, Juice, Water or Clean Beer Line;
Quality Guarantee: Any Defective for Carbonation Cap, Backed by 45 days Money-Back.

Learn More

Potential Uses:

PET Bottles as Growlers: These are generally intended to convert 1L and 2L bottles to growlers. Fill up a 1L or 2L PET bottle with your favorite homebrew. Put one of these on (purge the headspace by squeezing if you want to) and then pressurize for transport. This should help to reduce oxygen pickup and maintain carbonation levels.
Fine tune or rapidly carbonate beer: You can also use this cap to rapidly carbonate beer. Same process as for transport, just set your regulator to the proper pressure and shake or agitate the PET bottle to help introduce CO2. Or hook it up to CO2 and let it sit in you kegerator.
Draft Line Cleaning Projects: I have developed three draft line cleaning projects using similar SS Caps – Build A Recirculating Draft Line Cleaning Pump | Mark II Keg and Carboy Cleaner Draft Line Cleaning Pump Conversion | Building a Simple Ball Lock Draft Line Flushing Setup
Related Top Post: Fun with Carbonation Caps!

1/13 7 AM Central: These are on sale for just $9.99. Shipping is also free to many US addresses with Prime Membership [Try Prime for Free] or a qualifying order. Prices and availability can change quickly. Check product page for current info – More About Prices

PET Bottles Beer Carbonation Cap – Counter Pressure Bottle Filling with 5/16″ Barb, Carbonation Beer Soda Water Brewed Beer, Fits Most Soft Drink PET Bottles – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading →

Pressure Gauge – 0 to 60 PSI – by PIC Gauges + Our Spunding Build

More Info

Highlighted Features

Black Steel Case With Chrome Bezel
Brass Socket And Movement
Phosphor Bronze Bourdon Tube
Dry Non-Fillable
3-2-3% Accuracy

Learn More

A potential homebrew application for this is to use it as part of a Spunding Valve Build. A Spunding Valve allows you to ferment under pressure, naturally and precisely carbonate in the keg, fix over-carbonated beers and lots more. See: Build a Spunding Valve

PIC Gauge S101D-254D 2.5″ Dial, 0/60 psi Range, 1/4″ Male NPT Connection Size, Bottom Mount Single Scale Dry Pressure Gauge with a Black Steel Case, Brass Internals, Chrome Bezel, and Plastic Lens – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

PIC Gauges S101D-254D Bottom Mount Single Scale Dry Pressure Gauge w/ Black Steel Case, Brass Internals, Chrome Bezel, Plastic Lens, 2.5" Dial, 0/60 psi Range, 1/4" Male NPT

Control Devices - CR25-100 -CR25 CR Series Brass Pressure Relief Valve, 0-100 psi Adjustable Pressure Range, 1/4" Male NPT

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

Price, promotions and availability can change quickly. Check the product page for current price, description and availability. ssprod:B00FBQ351Y:ptr

Winters PEM Series Steel All Purpose Pressure Gauge + Our Spunding Valve Resource Post

Winters PEM Series Steel Dual Scale Economical All Purpose Pressure Gauge with Brass Internals, 0-100 psi/kpa, 2″ Dial Display, +/-3-2-3% Accuracy, 1/4″ NPT Bottom Mount

More Info

Highlighted Features

DRY PRESSURE GAUGE: Make sure your machine is functioning at peak performance! This pressure gauge is made of brass wetted parts for measuring non-corrosive liquid & gas pressure. Great for HVAC, pneumatic, hydraulic systems, air compressors & more.
DUAL SCALE GAUGE: This pressure gauge features a dual-scale gauge 0-15 psi/kPa and can be installed anywhere in the circuit to easily measure pressure at any point. With an acrylic lens for maximum clarity, providing accurate, clear readings at all times
STURDY & IP52 CERTIFIED: This circular dial is enclosed in a steel case for environmental protection and is IP52 certified for protection against dust or liquids. This pressure gauge is built to last, so you can count on it when the pressure mounts.
ACCURATE RESULT: Its display accuracy is + or - 3/2/3% over the entire range of the gauge (ASME B40.100 Grade B) & has a 1/4-inch NPT male connection in the lower mount. Perfect fit with no leaks and is easy to read.
PRODUCT DETAILS: Variation: PEM Economy Pressure Gauge. Dial Size: 2" (50mm.) Dimension: 3 x 2 x 1.2 inches. Accuracy: +/- 3-2-3%. Material: Bronze and Brass. Case: Steel painted Black. For non-clogging and non-corroding media.

Learn More

I use a similar sort of gauge gauge (different specs, manufacturer and model) in my Spunding Valve Build. A Spunding Valve allows you to ferment under pressure, naturally and precisely carbonate in the keg, fix over-carbonated beers and more. See: [Build a Spunding Valve].

Winters 2 inch Dial Size, Multi Function Economy Utility Dry Pressure Gauge, Brass Internals, Black Steel Case, Dual Scale 0-100 psi/kPa, 3-2-3% Accuracy, 1/4 inch NPT Bottom Mount, Pressure Gauge – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

THREE x Carbonation Caps for PET Bottles – works on gas AND liquid posts + Fun With Carbonation Caps!

More Info

Highlighted Features

Withstand 60-PSI Carbonation Pressure, Complete No Leaking Sealing O-Ring Design and Huge Upgrade From Old Plastic Version: MRbrew carbonation cap comes with necessary brewing sealing o-rings and washer replacemets to prevent leaks, there is a big flat gasket inside this carbonation cap compared to the old version plastic bottle filling cap, can run your carbonator at 60 psi pressure and hold pressure overnight, beer will not go flat, make a airtight seal and good fit for force carbonation.
Sealing Gasket is Not Easy to Fall Out and Include 5/16 Barb Fitting Spare O-ring: the inside rubber sealing gasket features a right size for being placed tightly inside carbonating cap, which will stay in on its own when unscrewing off bottle filling cap, also provide 5/16'' beer nipple barb sealing o-ring replacements even such o-ring is screwed inside getting well protected. unlike other polished finish carbonation caps, you can grip this plastic carbonation cap easily when removing.
Unique Carbonation Cap Keg Post is Perfect for Ball Lock System and Removable Beer Barb: carbonation cap features a unique keg post that has versatility and ease of use, can connect to both gas and liquid disconnects easily, beer 5/16'' hose barb not only enables carbonation cap to carbonate, but to be used for liquid connections and for cleaning as well. made of healthy plastic, no odors, no burrs or unfinished machining anywhere, will not bring strange smell to the carbonation drinks.
Screws onto Standard 2L Soda Bottles Very Securely: this soda drink bottle filling cap features a great accuracy 1-1/8-8UN female thread that can be comparable to the thread of stainless carbonation cap, merge with the plastic PET bottle threads very smoothly, seals the bottles well without needing much torque, screws on and off of bottles easily creating a perfect tight seal every time, excellent tool if you are making homebrewing and kegging.
Perfect for Various Brewing Occasions and Reduce CO2 Loss when Do Brewing Cleaning: carbonation cap is a cool way to re-carbonate beverage quickly, no foaming, great alternative for growlers, allows you to serve portable home brew beer, soda water, iced tea on barbecue, beach, lake or holiday parties, other outdoor activities, brings big convenience to mobile kegging. also can run the cleaner through beer lines from a small soda bottle preventing a larger keg from wasting more co2.

Learn More

Applications:

PET Bottles as Growlers: These are generally intended to convert 1L and 2L bottles to growlers. Fill up a 1L or 2L PET bottle with your favorite homebrew. Put one of these on (purge the headspace by squeezing if you want to) and then pressurize for transport. This should help to reduce oxygen pickup and maintain carbonation levels.
Fine tune or rapidly carbonate beer: You can also use this cap to rapidly carbonate beer. Same process as for transport, just set your regulator to the proper pressure and shake or agitate the PET bottle to help introduce CO2. Or hook it up to CO2 and let it sit in you kegerator.
Draft Line Cleaning Projects: I have developed three draft line cleaning projects using similar SS Caps – Build A Recirculating Draft Line Cleaning Pump | Mark II Keg and Carboy Cleaner Draft Line Cleaning Pump Conversion | Building a Simple Ball Lock Draft Line Flushing Setup
Related Top Post: Fun with Carbonation Caps!

MRbrew Plastic Carbonation Cap, 3 PCS Ball Lock Keg Post 5/16” Beer Line Nipple Barb Homebrew Kegging Soft Soda Drink PET Bottles Counter Pressure Bottle Filling Cap with Spare Sealing Gasket O-rings – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Continue reading →

Milton 1/4″ MNPT Schrader Valves, 2 Pack + adding a Schrader Valve to Your Corny Keg

Milton S-684-4 1/4″ MNPT Male Tank Valve, includes Protective Caps (Pack of 2)

These have lots of uses, but one potential project is adding a Schrader style valve to your corny keg.

Milton S-684-4 1/4″ MNPT Male Tank Valve, includes Protective Caps (Pack of 2) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

Adding a Schrader Valve to a Homebrew Keg

Milton S-684-4 1/4" MNPT Male Tank Valve, includes Protective Caps (Pack of 2)

Anderson Metals - 56103-04 Brass Pipe Fitting, Coupling, 1/4" x 1/4" Female Pipe

LASCO 17-6783 1/4-Inch Female Flare by 1/4-Inch Male Pipe Thread Brass Adapter

Dixon Valve & Coupling TTB75-5 White Industrial PTFE Tape, 3/4" (Pack of 5)

Make sure the components you use are compatible and rated for your intended application. Contact manufacturer with questions about suitability or a specific application. Always read and follow manufacturer directions.

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

FOUR x Carbonation Caps for PET Bottles – works on gas AND liquid posts

More Info

Highlighted Features

Withstand 60-PSI Carbonation Pressure, Complete No Leaking Sealing O-Ring Design and Huge Upgrade From Old Plastic Version: MRbrew carbonation cap comes with necessary brewing sealing o-rings and washer replacemets to prevent leaks, there is a big flat gasket inside this carbonation cap compared to the old version plastic bottle filling cap, can run your carbonator at 60 psi pressure and hold pressure overnight, beer will not go flat, make a airtight seal and good fit for force carbonation.
Sealing Gasket is Not Easy to Fall Out and Include 5/16 Barb Fitting Spare O-ring: the inside rubber sealing gasket features a right size for being placed tightly inside carbonating cap, which will stay in on its own when unscrewing off bottle filling cap, also provide 5/16'' beer nipple barb sealing o-ring replacements even such o-ring is screwed inside getting well protected. unlike other polished finish carbonation caps, you can grip this plastic carbonation cap easily when removing.
Unique Carbonation Cap Keg Post is Perfect for Ball Lock System and Removable Beer Barb: carbonation cap features a unique keg post that has versatility and ease of use, can connect to both gas and liquid disconnects easily, beer 5/16'' hose barb not only enables carbonation cap to carbonate, but to be used for liquid connections and for cleaning as well. made of healthy plastic, no odors, no burrs or unfinished machining anywhere, will not bring strange smell to the carbonation drinks.
Screws onto Standard 2L Soda Bottles Very Securely: this soda drink bottle filling cap features a great accuracy 1-1/8-8UN female thread that can be comparable to the thread of stainless carbonation cap, merge with the plastic PET bottle threads very smoothly, seals the bottles well without needing much torque, screws on and off of bottles easily creating a perfect tight seal every time, excellent tool if you are making homebrewing and kegging.
Perfect for Various Brewing Occasions and Reduce CO2 Loss when Do Brewing Cleaning: carbonation cap is a cool way to re-carbonate beverage quickly, no foaming, great alternative for growlers, allows you to serve portable home brew beer, soda water, iced tea on barbecue, beach, lake or holiday parties, other outdoor activities, brings big convenience to mobile kegging. also can run the cleaner through beer lines from a small soda bottle preventing a larger keg from wasting more co2.

Learn More

Applications:

PET Bottles as Growlers: These are generally intended to convert 1L and 2L bottles to growlers. Fill up a 1L or 2L PET bottle with your favorite homebrew. Put one of these on (purge the headspace by squeezing if you want to) and then pressurize for transport. This should help to reduce oxygen pickup and maintain carbonation levels.
Fine tune or rapidly carbonate beer: You can also use this cap to rapidly carbonate beer. Same process as for transport, just set your regulator to the proper pressure and shake or agitate the PET bottle to help introduce CO2. Or hook it up to CO2 and let it sit in you kegerator.
Draft Line Cleaning Projects: I have developed three draft line cleaning projects using similar SS Caps – Build A Recirculating Draft Line Cleaning Pump | Mark II Keg and Carboy Cleaner Draft Line Cleaning Pump Conversion | Building a Simple Ball Lock Draft Line Flushing Setup
Related Top Post: Fun with Carbonation Caps!

Continue reading →

Building a Dry Hopper for Corny Kegs – Dry Hop Under Pressure!

Thanks to /u/NachoTacocat on r/homebrew for this photo and build info!

Benefits of Fermenting Under Pressure + The Challenges of Dry Hopping Under Pressure

Fermenting under pressure has some great benefits. One of the challenges that using this method presents is… dry hopping. When fermenting under pressure the beer is carbonated. Adding dry hops to a fermented and carbonated beer, especially one at relatively warm fermentation temps equates to a Mentos+Diet Coke sort of situation. The hops provide lots and lots of nucleation points that can cause the beer to erupt expelling foam all over the place in the process denaturing head retaining proteins.

FermZilla fermenters from Kegland have a ready made solution called the Hop Bong. It allows you easily dry hop under pressure. Since the beer and dry hops are under pressure you don’t have foaming problems when dry hopping.

Continue reading →

Brennan Industries 1/4″ Male NPT to 1/4″ Female Flare – $5.90 + Build a Spunding Valve How & Why

Brennan Industries 6505-04-04 Steel Straight Tube Fitting, 1/4″-18 NPTF x 7/16″-20 SAE Thread, 1/4″ Male NPTF x 1/4″ Female JIC Swivel

This fitting is featured in our Spunding Valve Build in the Style 1 section of our build post. A Spunding Valve allows you to ferment under pressure, naturally and precisely carbonate in the keg, fix over-carbonated beers and more.

As of this posting this these are selling for just $5.90. Shipping is also free to many US addresses with Prime Membership [Try Prime for Free] or a qualifying order. Prices and availability can change quickly. Check product page for current info – More About Prices

Brennan Industries 6505-04-04 Steel Straight Tube Fitting, 1/4″-18 NPTF x 7/16″-20 SAE Thread, 1/4″ Male NPTF x 1/4″ Female JIC Swivel – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

Continue reading →

Building a Dry Hopper for Corny Kegs – Dry Hop Under Pressure!

Thanks to /u/NachoTacocat on r/homebrew for this photo and build info!

Benefits of Fermenting Under Pressure + The Challenges of Dry Hopping Under Pressure

Continue reading →

ABS Plastic Dustproof Waterproof IP65 Junction Box

LMioEtool ABS Plastic Dustproof Waterproof IP65 Junction Box Hinged Shell Universal Electrical Project Enclosure Gray, with PC Transparent Clear Cover 11.4 x 7.5 x 5.5inch(290 x190 x140mm)

More Info

Highlighted Features

Product Name : Junction box; Waterproof rating : IP65.
Material: ABS,PC ; Net Weight: 820g; Main Color: Light Gray (For Box Body), Transparent（For box cover）
The Enclosure box features two or three plastic latches for added security and locking; moisture proof, sunscreen, anti-corrosion, durable for years use.
This electrical junction box is easy to operate and repair, no cable cutting, more convenient.
Outer Size(Approx.):11.4" x 7.5" x 5.5"(290mmx190mmx140mm)(L*W*H); Inner Size(Approx.): 10.4" x 6.7" x 5.2"/265mm x 170mm x131mm(L*W*H)- -* Tips: in order to confirm the detailed installation dimensions, please refer to our detail image, which shows specific internal dimensions of the product. (Allowable Error: 2mm).

Learn More

Use for your homebrew-related project and more.

Note that multiple sizes are available at varying costs.

LMioEtool ABS Plastic Dustproof Waterproof IP65 Junction Box Hinged Shell Universal Electrical Project Enclosure Gray, with PC Transparent Clear Cover 11.4 x 7.5 x 5.5inch(290 x190 x140mm) – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

Measureman Digital Pressure Gauge & My Spunding Valve Build

Measureman 2-1/2″ Dial Size Digital Air Pressure Gauge with 1/4” NPT Bottom Connector and Protective Boot, 0-60psi, Accuracy 1%, Battery Powered, with LED Light

More Info

Highlighted Features

For pneumatic, air pressure measuring, typical for tire gauge, tire inflator, air pressure system etc.
Dial size: 2-1/2", blue backlight
Plastic case and protective boot,
Solid brass connection, standard 1/4"NPT male
0-60psi, bar, kg/cm2, kpa, Accuracy:1%

Learn More

Note from HBF: For whatever reason this offering seems to periodically change. The one I’m intending to link to is a 2 1/2 dial with 1/4″ NPT that reads 0 to 60 PSI. It’s possible a different variation will show up.

Measureman 2-1/2″ Dial Size Digital Air Pressure Gauge with 1/4” NPT Bottom Connector and Protective Boot, 0-60psi, Accuracy 1%, Battery Powered, with LED Light – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!

Set of 4 Heavy Duty Swivel Casters

Set of Four Heavy Duty Casters

More Info

From the product description, check product page for current description, price and availability:

Highlighted Features

Standard: A set of 4 caster wheels, 2 inch Polyurethane (PU) Swivel caster wheels,a box with screwdrivers, screws and iron washers
Wide use: widely used indoor and outdoor, trolleys, workbench, furniture, shelves and other items commonly found in workshops, garages, kitchens, offices etc.
Heavy duty and double ball bearing: Our 2 inch heavy duty top plate swivel caster wheels can carry 150Lbs, double bearing.
Double brake: Our top plate swivel caster wheels have double brake, it can brake the rotation direction of the bottom plate and the direction of the wheel forward, which is easy to operate.
Silence: Silent, easy to push, strong load capacity.

Learn More

Note from HBF: Your around-the-brewery project may need some casters.

ASHGOOB 2″ Caster Wheels Set of 4, Heavy Duty Casters with Brake, No Noise Locking Casters with Polyurethane (PU) Wheels, Swivel Plate Castors Pack of 4 – affiliate link, note that multiple variations of this product may be available, as such a different version may appear at this link

This post contains affiliate links. We may make a commission when you use our Amazon links. This will never cost you extra. Thank you for supporting Homebrew Finds!