From the product description, check product page for current description, price and availability:

The 65L/17.1G 220V BrewZilla is the ultimate all-in-one system for homebrewers seeking more volume, power, precision, convenience, and the gold standard in brewing, repeatability!

17.1 gallon total capacity with a finished beer output of 10-12 gallons
220V power to ramp up temperatures faster and provide a more vigorous boil.
Digital controller capable of programmed mash steps, boil addition timers and delayed start
Built-in pump for constant recirculation during mash or whirlpooling
Wort chiller included!
We’ve seen a lot of all-in-one systems over the years, but none are as feature-packed and affordable as the BrewZilla. While other units simply maintain your set temperature, the BrewZilla features a sophisticated digital controller which can be programmed with a full mash schedule, executing each step automatically. The built-in pump will continuously recirculate wort during the mash for more even heat distribution and higher efficiency, but thanks to the integrated camlock fitting, it has even more functionality. Add the optional whirlpool arm to make your late hop additions pop and speed up chilling time, or connect a camlock fitting and tubing to transfer wort to your fermenter. These are just a couple of reasons why MoreBeer! loves the BrewZilla, but there are so many More!

Our Top 10 Favorite Features:

Sophisticated digital controller capable of programmed mash steps, boil addition timers and delayed start
Built-in pump for constant recirculation during mash or whirlpooling and transferring with optional accessories
Full depth malt pipe for higher mash efficiency and capable of running small batches without a pricey adapter
Multiple power modes to cover each step of the brew day – low power to gently heat your mash up to full power for a rolling boil
Wort chiller included! Perfectly sized for this system and adds even more value to your purchase of the BrewZilla
High capacity brewhouse – with a volume of over 17 gallons, you can fit more grain and more wort to make MoreBeer!
Single wall design doesn’t trap in heat – chill your wort quickly after the boil!
Super convenient bottom handle makes lifting/pouring a breeze
Rubber feet keep the boiler lifted off the ground and safely above any spills that may occur
Affordable! This is the best price for an all-in-one brewing system you’ll find, period.
Are you looking for an awesome, easy-to-use, single vessel system to brew 10-gallon batches? The BrewZilla features built-in elements for heating and boiling, programmable mash schedule and delayed start, a built-in pump for recirculation, an onboard water-resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. The compact design makes this unit easy to store when not in use. Not brewing 10-gallon batches every brew day? No problem! The BrewZilla works just as well for 5-gallon batches, and with so much power, you’ll get your temperatures up even faster.

The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you’ll never miss the mark for hop additions.

To get the Wort Chiller Connection Kit for free, add the item to your cart along with the BrewZilla and use code ZILLAKIT at checkout.

New accessory! Check out the BrewZilla Whirlpool Arm, which uses the unit’s internal pump to recirculate and spin the wort, improving hop extraction and chill times. No more stirring!

Automatic Step Mashing!
One of the coolest features of the BrewZilla is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the “S1-S6” button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the BrewZilla will sound an alarm and hold the last set temperature.

The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the BrewZilla ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day.

Recirculating Mash with Full Depth Malt Pipe
The built-in magnetic drive pump easily recirculates wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed.

Some competing models advertise their perforated malt pipes as “high flow”, but what they don’t mention is how this affects efficiency. When recirculating the mash, wort will escape through the side perforations rather than passing through the grain at the bottom-most end of the malt pipe which can lead to lower efficiency. The BrewZilla’s malt pipe is designed so that recirculating wort must pass through the entire grain bed before escaping through the false bottom and being pumped over the top of the grain bed again. If you’re worried about the flow rate, simply add a pound or two of rice hulls to your grain bill. This is especially recommended when brewing with a high level of wheat, oat, or flaked grains.

Power & Heating Control
This very capable 15amp brewery has over 3 kilowatts of power so you can get up to boil in no time. 220V outlet required! The BrewZilla has been made with ultra-low watt density elements, which means less caramelization and also makes this unit capable of producing very light beers with very little maillard effect. This is also particularly useful for high gravity beers that can get some degree of scorching in other electric breweries with higher watt density.

Triple heating elements run off of a single 220 volt plug and have individual switches allowing for more control over the heating process. The elements are 2000, 1000 and 500 watts for a combined 3500 watts! Use all three elements when you need to ramp up the temperature quickly, either to quickly get to your mash temp or to rapidly go from your mash temp to boiling. Use only one of the elements when you want to hold a desired temperature.

We highly recommend adding the optional BrewZilla Neoprene Jacket to help reduce heating times and maintain a more vigorous boil. The extra thick neoprene jacket is custom designed to insulate the entire kettle portion of the BrewZilla while staying out of the way of the ball valve and handles. The jacket can help you acheive up to 10% faster heat up times and cut heat loss from the boiler in half.

Built-in magnetic drive pump to easily recirculate the wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed.

The digital control panel makes it easy to see the current temperature and set the temperature you want. You can also set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or get up in the morning. The digital controller is also water resistant so don’t worry about spills or some water dripping down the side. This controller is built for brewing!

The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it from the BrewZilla and tabs at the base so you can set the malt pipe over the system to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging.

The included stainless wort chiller is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings to connect to a hose, hose bib, or faucet.

What MoreBeer! loves about this product: Homebrewing is trending in the direction of all-in-one, all-grain brewing systems, but there are few options when it comes to brewing 10-gallon batches. The BrewZilla not only allows for 10-gallon batches, but the cost is half of the next comparable system. We’ve brewed on all the systems and we can truly say the BrewZilla series is the easiest to use. We feel confident that a lot of first-time brewers could buy this and use it with ease. At the same time, quite a few of our experienced, all-grain brewing staff are buying these units to brew at home. The BrewZilla is considerably compact for a 10-gallon system because the pump is built-in at the bottom of the unit. When not in use, the system can be packed up into a box that is 24″ x 24″ x 34″ tall and moved around with ease, which makes it perfect for guys and gals that have space constraints. All in all a great buy and highly recommended. Please note you will need a few extra pieces of hardware to connect the wort chiller and at least 2′ of silicone tubing for the sparge arm.

Use the Pump for More Than Just Recirculation!
One of the surprisingly handy features of the BrewZilla is that the recirculation pipe features a female camlock. This allows you to hook up other accessories and use the unit’s pump for more than just recirculating wort. With a male camlock and silicone tubing, for example, you can use the internal pump to push wort through a plate chiller or counterflow chiller. Check out our selection of camlock fittings here.

Features:

Gen 3.1.1
Stainless steel construction
17.1 gallon total capacity with a finished beer output of 10-12 gallons
Digital temperature controller
220V power
NEMA 6-30R plug
Triple heating elements for total control (2000, 1000 and 500 watts)
Stainless steel 1/2 in ball valve for draining (don’t have to use the pump)
Immersion wort chiller included
Stainless steel malt pipe/basket
Stamped in volume markers
Glass lid
Magnetic drive pump for recirculation
Recirculation arm
Temperature reads in °F or °C (press and hold temp button for several seconds to adjust)
Approximately 36″ H (with recirculation arm) x 16″ D
AlcoEngine Still ready with the purchase of a Distillation Lid
You will Need:

2′ of H985 1/2″ ID Silicone tubing for sparging and draining
To connect included Chiller: (20′) of D1710 1/2″ ID beverage tubing (or whatever length required, (3) H950 hose clamps and (1) brass hose by thread adaptor (H508).
These items come in the Wort Chiller Connection Kit, add the kit to your cart and use code ZILLAKIT at checkout.

---